arrow_back
Module 1: Introduction to SBC 302 – General Provisions
1-Understanding-SBC-302-General-Provisions-for-Saudi-Construction
Submodule 1.1: Purpose, Scope, and Application
Submodule 1.2: Definitions and Key Terminologies
Submodule 1.3: Responsibilities of Owners, Designers, and Contractors
Module 2: Administrative Requirements
2-Saudi-Building-Code-SBC-302-Administrative-Requirements
Submodule 2.1: Authority and Enforcement Procedures
Submodule 2.2: Permits, Inspections, and Documentation
Submodule 2.3: Violations, Penalties, and Appeals
Module 3: Design Criteria and Load Considerations
3-Design-Criteria-and-Load-Considerations
Submodule 3.1: Dead, Live, and Environmental Loads
Submodule 3.2: Load Combinations and Design Philosophy
Submodule 3.3: Structural Stability and Serviceability
Module 4: Structural Systems and Materials
4-Structural-Systems-and-Materials
Submodule 4.1: Reinforced Concrete Construction
Submodule 4.2: Structural Steel and Composite Systems
Submodule 4.3: Masonry, Timber, and Alternative Materials
Module 5: Foundations and Geotechnical Requirements
5-Foundations-and-Geotechnical-Requirements
Submodule 5.1: Site Investigation and Soil Classification
Submodule 5.2: Bearing Capacity and Settlement Criteria
Submodule 5.3: Foundation Design and Drainage Provisions
Module 6: Construction Documentation and Drawings
6-Construction-Documentation-and-Drawings
Submodule 6.1: Minimum Requirements for Design Drawings
Submodule 6.2: As-Built and Record Documentation
Submodule 6.3: Approval and Review Procedures
Module 7: Construction Site Management and Safety
7-Construction-Site-Management-and-Safety
Submodule 7.1: Site Access, Fencing, and Security
Submodule 7.2: Safety in Excavation and Structural Work
Submodule 7.3: Emergency and Hazard Control Measures
Module 8: Structural Integrity During Construction
8-Structural-Integrity-During-Construction
Submodule 8.1: Temporary Structures and Supports
Submodule 8.2: Construction Loading and Staging
Submodule 8.3: Monitoring and Quality Verification
Module 9: Concrete Construction Practices
9-Concrete-Construction-Practices-in-Saudi-Building-Code
Submodule 9.1: Mix Design and Material Quality
Submodule 9.2: Formwork, Placement, and Curing
Submodule 9.3: Reinforcement Placement and Inspection
Module 10: Steel Construction Practices
10-Steel-Construction-Practices
Submodule 10.1: Fabrication and Erection Standards
Submodule 10.2: Welding, Bolting, and Connections
Submodule 10.3: Corrosion Protection and Fireproofing
Module 11: Masonry and Blockwork Construction
11-Masonry-and-Blockwork-Construction
Submodule 11.1: Units, Mortar, and Grout Specifications
Submodule 11.2: Masonry Laying, Bonding, and Reinforcement
Submodule 11.3: Quality Control and Testing Procedures
Module 12: Concrete Formwork and Reinforcement Detailing
Submodule 12.1: Formwork Design and Alignment
Submodule 12.2: Reinforcement Cutting and Bending Rules
Submodule 12.3: Tolerances and Inspection Requirements
Module 13: Waterproofing and Moisture Protection
Submodule 13.1: Foundation Waterproofing and Damp Proofing
Submodule 13.2: Roof and Wall Moisture Protection
Submodule 13.3: Materials and Testing Standards
13-Waterproofing-and-Moisture-Protection_pdf
Module 14: Fire Resistance and Structural Safety
14-Fire-Resistance-and-Structural-Safety-in-the-Saudi-Building-Code
Submodule 14.1: Fire Resistance Ratings of Building Elements
Submodule 14.2: Fire Separation and Compartmentation
Submodule 14.3: Fireproof Materials and Coatings
Module 15: Construction Tolerances and Quality Assurance
15-Construction-Tolerances-and-Quality-Assurance
Submodule 15.1: Dimensional Tolerances for Structural Works
Submodule 15.2: Material Acceptance and Inspection Testing
Submodule 15.3: Documentation and Quality Records
Module 16: Construction in Seismic and Wind Zones
Submodule 16.1: Seismic Design and Reinforcement Detailing
Submodule 16.2: Wind Load Resistance and Stability
Submodule 16.3: Post-Event Inspection and Strengthening
16-Construction-in-Seismic-and-Wind-Zones_pdf
Module 17: Temporary Works and Demolition
Submodule 17.1: Scaffolding and Shoring Requirements
Submodule 17.2: Demolition Procedures and Safety
Submodule 17.3: Waste Handling and Environmental Compliance
17-Temporary-Works-and-Demolition_pdf
Module 18: Testing, Inspection, and Compliance
Submodule 18.1: Material and Structural Testing Requirements
Submodule 18.2: Field Inspections and Non-Destructive Testing
Submodule 18.3: Compliance Reports and Final Certification
18-Testing-Inspection-and-Compliance_pdf
Module 19: Construction Supervision and Quality Control
Submodule 19.1: Supervision Roles and Responsibilities
Submodule 19.2: Site Quality Control Procedures
Submodule 19.3: Non-Conformance and Corrective Actions
19-Construction-Supervision-and-Quality-Control_pdf
Module 20: Completion, Handover, and Maintenance
Submodule 20.1: Final Inspections and Approval
Submodule 20.2: Handover Documentation and Record Keeping
Submodule 20.3: Maintenance, Repair, and Post-Construction Obligations
20-Completion-Handover-and-Maintenance_pdf
